产品展示
您现在的位置:
首页
/
/
/
/
40G多模双纤300米 SRBD 850波长
浏览量:
1016

40G多模双纤300米 SRBD 850波长

It is a Four-Channel,Pluggable, LC Duplex, Fiber-Optic QSFP+ Transceiver for 40 Gigabit Ethernet Applications. This transceiver is a high performance module for short-range duplex data communication and interconnect applications. It integrates four electrical data lanes in each direction into transmission over a single LC duplex fiber optic cable. Each electrical lane operates at 10.3125 Gbps and conforms to the 40GE XLPPI interface.
零售价
0.0
市场价
0.0
浏览量:
1016
产品编号
数量
-
+
库存:
产品描述
产品特征
技术参数
尺寸图
订购信息

It is a Four-Channel,Pluggable, LC Duplex, Fiber-Optic QSFP+ Transceiver for 40 Gigabit Ethernet Applications. This transceiver is a high performance module for short-range duplex data communication and interconnect applications. It integrates four electrical data lanes in each direction into transmission over a single LC duplex fiber optic cable. Each electrical lane operates at 10.3125 Gbps and conforms to the 40GE XLPPI interface.

The transceiver internally multiplexes an XLPPI 4x10G interface into two 20Gb/s electrical channels, transmitting and receiving each optically over one simplex LC fiber using bi-directional optics. This results in an aggregate bandwidth of 40Gbps into a duplex LC cable. This allows reuse of the installed LC duplex cabling infrastructure for 40GbE application. Link distances up to 100 m using OM3 and 150m using OM4 optical fiber are supported. These modules are de- signed to operate over multimode fiber systems using a nominal wavelength of 850nm on one end and 900nm on the other end. The electrical interface uses a 38 contact QSFP+ type edge connector. The optical interface uses a conventional LC duplex connector.

扫二维码用手机看
未找到相应参数组,请于后台属性模板中添加

 Features

² Compliant to the 40GbE XLPPI electrical specification per IEEE 802.3ba-2010

² Compliant to QSFP+ SFF-8436 Specification

² Aggregate bandwidth of > 40Gbps

² Operates at 10.3125 Gbps per electrical channel with 64b/66b encoded data

² QSFP MSA compliant

² Capable of over 100m transmission on OM3 Multimode Fiber (MMF)and 150m on OM4 MMF

² Single +3.3V power supply operating  

² Without digital diagnostic functions  

² Temperature range 0°C to 70°C  

² RoHS Compliant Part

² Utilizes a standard LC duplex fiber cable allowing reuse of existing cable infrastructure

Applications:

² 40 Gigabit Ethernet interconnects

² Datacom/Telecom switch & router connections

² Data aggregation and backplane applications

² Proprietary protocol and density applications

Absolute Maximum Ratings

 

Parameter

Symbol

Min.

Typical

Max.

Unit

Storage Temperature

TS

-40

 

+85

°C

Supply Voltage

VCCT, R

-0.5

 

4

V

Relative Humidity

RH

0

 

85

%

Recommended Operating Environment:

 

Parameter

Symbol

Min.

Typical

Max.

Unit

Case operating Temperature

TC

0

 

+70

°C

Supply Voltage

VCCT, R

+3.13

3.3

+3.47

V

Supply Current

ICC

 

 

1000

mA

Power Dissipation

PD

 

 

3.5

W

Electrical Characteristics (TOP = 0 to 70 °C, VCC = 3.13 to 3.47 Volts

 

Parameter

Symbol

Min

Typ

Max

Unit

Note

Data Rate per Channel

 

-

10.3125

11.2

Gbps

 

Power Consumption

 

-

2.5

3.5

W

 

Supply Current

Icc

 

0.75

1.0

A

 

Control I/O Voltage-High

VIH

2.0

 

Vcc

V

 

Control I/O Voltage-Low

VIL

0

 

0.7

V

 

Inter-Channel Skew

TSK

 

 

150

Ps

 

RESETL Duration

 

 

10

 

Us

 

RESETL De-assert time

 

 

 

100

ms

 

Power On Time

 

 

 

100

ms

 

Transmitter

Single Ended Output Voltage Tolerance

 

0.3

 

4

V

1

Common mode Voltage Tolerance

 

15

 

 

mV

 

Transmit Input Diff Voltage

VI

120

 

1200

mV

 

Transmit Input Diff Impedance

ZIN

80

100

120

 

 

Data Dependent Input Jitter

DDJ

 

 

0.1

UI

 

Data Input Total Jitter

TJ

 

 

0.28

UI

 

Receiver

Single Ended Output Voltage Tolerance

 

0.3

 

4

V

 

Rx Output Diff Voltage

Vo

 

600

800

mV

 

Rx Output Rise and Fall Voltage

Tr/Tf

 

 

35

ps

1

Total Jitter

TJ

 

 

0.7

UI

 

Deterministic Jitter

DJ

 

 

0.42

UI

 

Note:

1. 2080%

 

Optical Parameters(TOP = 0 to 70 °C, VCC = 3.0 to 3.6 Volts)

 

Parameter

Symbol

Min

Typ

Max

Unit

Ref.

Transmitter

Optical Wavelength CH1

λ

832

850

868

nm

 

Optical Wavelength CH2

λ

882

900

918

nm

 

RMS Spectral Width

Pm

 

0.5

0.65

nm

 

Average Optical Power per Channel

Pavg

-4

-2.5

+5.0

dBm

 

Laser Off Power Per Channel

Poff

 

 

-30

dBm

 

Optical Extinction Ratio

ER

3.5

 

 

dB

 

Relative Intensity Noise

Rin

 

 

-128

dB/HZ

1

Optical Return Loss Tolerance

 

 

 

12

dB

 

Receiver

Optical Center Wavelength CH1

λ

882

900

918

nm

 

Optical Center Wavelength CH2

λ

832

850

868

nm

 

Receiver Sensitivity per Channel

R

 

-11

 

dBm

 

Maximum Input Power

PMAX

+0.5

 

 

dBm

 

Receiver Reflectance

Rrx

 

 

-12

dB

 

LOS De-Assert

LOSD

 

 

-14

dBm

 

LOS Assert

LOSA

-30

 

 

dBm

 

LOS Hysteresis

LOSH

0.5

 

 

dB

 

 Note

1. 12dB Reflection

Page02 is User EEPROM and its format decided by user.

 

The detail description of low memory and page00.page03 upper memory please see SFF-8436 document.

 

Timing for Soft Control and Status Functions

 

Parameter

Symbol

Max

Unit

Conditions

Initialization Time

t_init

2000

ms

Time from power on1, hot plug or rising edge of Reset until the module is fully functional2

Reset Init Assert Time

t_reset_init

2

μs

A Reset is generated by a low level longer than the minimum reset pulse time present on the ResetL pin.

Serial Bus Hardware Ready Time

t_serial

2000

ms

Time from power on1 until module responds to data transmission over the 2-wire serial bus

Monitor Data Ready

Time

t_data

2000

ms

Time from power on1 to data not ready, bit 0 of Byte 2, deasserted and IntL asserted

Reset Assert Time

t_reset

2000

ms

Time from rising edge on the ResetL pin until the module is fully functional2

LPMode Assert Time

ton_LPMode

100

μs

Time from assertion of LPMode (Vin:LPMode =Vih) until module power consumption enters lower Power Level

IntL Assert Time

ton_IntL

200

ms

Time from occurrence of condition triggering IntL until Vout:IntL = Vol

IntL Deassert Time

toff_IntL

500

μs

toff_IntL 500 μs Time from clear on read3 operation of associated flag until Vout:IntL = Voh. This includes deassert times for Rx LOS, Tx Fault and other flag bits.

Rx LOS Assert Time

ton_los

100

ms

Time from Rx LOS state to Rx LOS bit set and IntL asserted

Flag Assert Time

ton_flag

200

ms

Time from occurrence of condition triggering flag to associated flag bit set and IntL asserted

Mask Assert Time

ton_mask

100

ms

Time from mask bit set4 until associated IntL assertion is inhibited

Mask De-assert Time

toff_mask

100

ms

Time from mask bit cleared4 until associated IntlL operation resumes

ModSelL Assert Time

ton_ModSelL

100

μs

Time from assertion of ModSelL until module responds to data transmission over the 2-wire serial bus

ModSelL Deassert Time

toff_ModSelL

100

μs

Time from deassertion of ModSelL until the module does not respond to data transmission over the 2-wire serial bus

Power_over-ride or

Power-set Assert Time

ton_Pdown

100

ms

Time from P_Down bit set 4 until module power consumption enters lower Power Level

Power_over-ride or Power-set De-assert Time

toff_Pdown

300

ms

Time from P_Down bit cleared4 until the module is fully functional3

Note

1. Power on is defined as the instant when supply voltages reach and remain at or above the minimum specified value.

2. Fully functional is defined as IntL asserted due to data not ready bit, bit 0 byte 2 de-asserted.

3. Measured from falling clock edge after stop bit of read transaction.

4. Measured from falling clock edge after stop bit of write transaction.

 

Pin Assignment

 

                                                                             Diagram of Host Board Connector Block Pin Numbers and Name

 

Pin Description

 

Pin

Logic

Symbol

Name/Description

Ref.

1

 

GND

Ground

1

2

CML-I

Tx2n

Transmitter Inverted Data Input

 

3

CML-I

Tx2p

Transmitter Non-Inverted Data output

 

4

 

GND

Ground

1

5

CML-I

Tx4n

Transmitter Inverted Data Output

 

6

CML-I

Tx4p

Transmitter Non-Inverted Data Output

 

7

 

GND

Ground

1

8

LVTTL-I

ModSelL

Module Select

 

9

LVTTL-I

ResetL

Module Reset

 

10

 

VccRx

+3.3V Power Supply Receiver

2

11

LVCMOS-I/O

SCL

2-Wire Serial Interface Clock

 

12

LVCMOS-I/O

SDA

2-Wire Serial Interface Data

 

13

 

GND

Ground

1

14

CML-O

Rx3p

Receiver Inverted Data Output

 

15

CML-O

Rx3n

Receiver Non-Inverted Data Output

 

16

 

GND

Ground

1

17

CML-O

Rx1p

Receiver Inverted Data Output

 

18

CML-O

Rx1n

Receiver Non-Inverted Data Output

 

19

 

GND

Ground

1

20

 

GND

Ground

1

21

CML-O

Rx2n

Receiver Inverted Data Output

 

22

CML-O

Rx2p

Receiver Non-Inverted Data Output

 

23

 

GND

Ground

1

24

CML-O

Rx4n

Receiver Inverted Data Output

 

25

CML-O

Rx4p

Receiver Non-Inverted Data Output

 

26

 

GND

Ground

1

27

LVTTL-O

ModPrsL

Module Present

 

28

LVTTL-O

IntL

Interrupt

 

29

 

VccTx

+3.3V Power Supply Transmitter

2

30

 

Vcc1

+3.3V Power Supply

2

31

LVTTL-I

LPMode

Low Power Mode

 

32

 

GND

Ground

1

33

CML-I

Tx3p

Transmitter Inverted Data Output

 

34

CML-I

Tx3n

Transmitter Non-Inverted Data Output

 

35

 

GND

Ground

1

36

CML-I

Tx1p

Transmitter Inverted Data Output

 

37

CML-I

Tx1n

Transmitter Non-Inverted Data Output

 

38

 

GND

Ground

1

Notes:

1. GND is the symbol for single and supply(power) common for QSFP modules, All are common within the QSFP module and all module voltages are referenced to this potential otherwise noted. Connect these directly to the host board signal common ground plane. Laser output disabled on TDIS >2.0V or open, enabled on TDIS <0.8V.

2. VccRx, Vcc1 and VccTx are the receiver and transmitter power suppliers and shall be applied concurrently. Recommended host board power supply filtering is shown below. VccRx, Vcc1 and VccTx may be internally connected within the QSFP transceiver module in any combination. The connector pins are each rated for maximum current of 500mA.

 

Recommended Circuit

Mechanical Dimensions

JHAQC03

  40Gb/s 100m QSFP+, Bi-Di, Duplex LC Hot Pluggable, 850/900nm, VCSEL, Multimode

锦昊安

7*24小时售后支持

锦昊安

安全技术解决方案

锦昊安

研究开发创新

锦昊安

资质认证

锦昊安

咨询电话:0755-81483343

产品咨询:13316858670 
技术邮箱:cfc@jha-tech.com

传真:0755-8148331

网址:www.jha-tech.com.cn

邮编:518000

地址:深圳市龙华区大浪街道横朗社区联建科技工业园厂房5栋3层 

锦昊安

手机扫一扫

 Copyright © 深圳市锦昊安科技有限公司 All rights reserved         粤ICP备19135367号        网站建设:中企动力  深圳