产品中心
深圳市锦昊安科技有限公司是一家专门为恶劣和苛刻环境设计的硬化以太网、PoE和光纤连接产品的制造商。
产品中心
155M 多模 2Km 850nm | 双光纤 SFP 收发器 JHA3202-85
-
- 高达 155Mb/s 的数据链路
- 热插拔
- 双工 LC 连接器
- 在 50/125μm MMF 上可达 2 公里
- 850nm VCSEL激光发射器
- 单+3.3V电源
- 最大功率<1W
- 工业/扩展/商业工作温度范围：-40°C 至 85°C/-5°C 至 85°C/-0°C 至 70°C 提供版本
- 符合 RoHS 标准且无铅
-
♦ SONET OC-3/SDH STM-1
♦ Fast Ethernet
♦ Other Optical Links
产品分类：
SFP模块
155M SFP
155M双光纤
- 产品描述
- 尺寸
- 订单信息
- 下载
- 应用
-
描述：
JHA 的 JHA3202-85 收发器是一款具有双工 LC 光学接口的高性能、高性价比模块。用于高速信号和 LVTTL 控制和监控信号的标准交流耦合 CML。接收部分使用PIN接收器，发射器使用850nm VCSEL激光器，高达14dB的链路预算确保该模块在SONET OC-3/SDH STM-1 2Km应用。
• 绝对最大额定值
范围
象征 分钟_ 典型的 最大。 单元 储存温度 T S
-40
+85
摄氏度
电源电压 电压CC
-0.5
4
在
相对湿度 相对湿度
0
85
%
• 推荐的 操作环境：
范围
象征 分钟_ 典型的 最大。 单元 外壳工作温度 工业的 热电偶_
-40
85
摄氏度
扩展 -5
85
摄氏度
商业的 0
+70
摄氏度
电源电压 电压CC
3.135
3.465
在
电源电流 集成电路
280
嘛
浪涌电流 我激增
集成电路+30
嘛
最大功率 P最大值
1
在
• Electrical Characteristics(TOP = -40 to 85°C, VCC = 3.135 to 3.465 Volts)
Parameter
Symbol Min. Typical Max. Unit Note Transmitter Section: Input differential impedance Rin
90
100
110
W
1
Single ended data input swing Vin PP
250
1200
mVp-p
Transmit Disable Voltage VD
Vcc – 1.3
Vcc
V
2
Transmit Enable Voltage VEN
Vee
Vee+ 0.8
V
Transmit Disable Assert Time Tdessert
10
us
Receiver Section: Single ended data output swing Vout,pp
300
800
mv
3
Data output rise time tr
500
ps
4
Data output fall time tf
500
ps
4
LOS Fault Vlosfault
Vcc – 0.5
VCC_host
V
5
LOS Normal Vlos norm
Vee
Vee+0.5
V
5
Power Supply Rejection PSR
100
mVpp
6
Note:
- AC coupled.
- Or open circuit.
- Into 100 ohm differential termination.
- 20 – 80 %
- LOS is LVTTL. Logic 0 indicates normal operation; logic 1 indicates no signal detected.
- All transceiver specifications are compliant with a power supply sinusoidal modulation of 20 Hz to 1.5MHz up to specified value applied through the power supply filtering network shown on page 23 of the Small Form-factor Pluggable (SFP) Transceiver Multi-Source Agreement (MSA), September 14, 2000.
• Optical Parameters(TOP = -40 to 85°C, VCC = 3.135 to 3.465 Volts)
Parameter
Symbol Min. Typical Max. Unit Note Transmitter Section: Center Wavelength λc
840
850
860
nm
Spectral Width σ
0.85
nm
Optical Output Power Pout
-10
-3
dBm
1
Optical Rise/Fall Time tr / tf
500
ps
2
Extinction Ratio ER
8.2
dB
Generated Jitter (peak to peak) JTXp-p
0.07
UI
3
Generated Jitter (rms) JTXrms
0.07
UI
3
Eye Mask for Optical Output Compliant with G.957(class 1 laser safety) Receiver Section: Optical Input Wavelength λc
770
870
nm
Receiver Overload Pol
-8
dBm
4
RX Sensitivity Sen
-24
dBm
4
RX_LOS Assert LOS A
-40
dBm
RX_LOS De-assert LOS D
-25
dBm
RX_LOS Hysteresis LOS H
0.5
dB
General Specifications: Data Rate BR
155
Mb/s
Bit Error Rate BER
10-12
Max. Supported Link Length on 50/125μm MMF@155Mb/s LMAX
2
km
Total System Budget LB
14
dB
Note
- The optical power is launched into MMF.
- 20-80%.
- Jitter measurements taken using Agilent OMNIBERT 718 in accordance with GR-253.
- Measured with PRBS 27-1 at 10-12 BER
• Pin Assignment
Diagram of Host Board Connector Block Pin Numbers and Name
Diagram of Host Board Connector Block Pin Numbers and Names
• Pin Function Definitions
Pin No
Name
Function
Plug Seq
Notes
1 VeeT Transmitter Ground 1 1 2 TX Fault Transmitter Fault Indication 3 3 TX Disable Transmitter Disable 3 2 4 MOD-DEF2 Module Definition 2 3 5 MOD-DEF1 Module Definition 1 3 3 6 MOD-DEF0 Module Definition 0 3 3 7 Rate Select Not Connected 3 4 8 LOS Loss of Signal 3 5 9 VeeR Receiver Ground 1 1 10 VeeR Receiver Ground 1 1 11 VeeR Receiver Ground 1 12 RD- Inv. Received Data Out 3 6 13 RD+ Received Data Out 3 6 14 VeeR Receiver Ground 3 1 15 VccR Receiver Power 2 1 16 VccT Transmitter Power 2 17 VeeT Transmitter Ground 1 18 TD+ Transmit Data In 3 6 19 TD- Inv. Transmit In 3 6 20 VeeT Transmitter Ground 1 Notes:
- Circuit ground is internally isolated from chassis ground.
- Laser output disabled on TDIS >2.0V or open, enabled on TDIS <0.8V.
- Should be pulled up with 4.7k – 10 kohms on host board to a voltage between 2.0V and 3.6V. MOD_DEF(0) pulls line low to indicate module is plugged in.
- Rate select is not used
- LOS is open collector output. Should be pulled up with 4.7k – 10 kohms on host board to a voltage between 2.0V and 3.6V. Logic 0 indicates normal operation; logic 1 indicates loss of signal.
- AC Coupled
• SFP Module EEPROM Information
The SFP modules implement the 2-wire serial communication protocol as defined in the SFP -8472. The serial ID information of the SFP modules can be accessed through the I2C interface at address A0h.
EEPROM Serial ID Memory Contents (A0h)
Data Address
Length
(Byte)
Name of
Length
Description and Contents
Base ID Fields 0
1
Identifier
Type of Serial transceiver (03h=SFP) 1
1
Reserved
Extended identifier of type serial transceiver (04h) 2
1
Connector
Code of optical connector type (07=LC) 3-10
8
Transceiver
11
1
Encoding
NRZ(03h) 12
1
BR, Nominal
Nominal baud rate, unit of 100Mbps 13-14
2
Reserved
(0000h) 15
1
Length(9um)
Link length supported for 9/125um fiber, units of 100m 16
1
Length(50um)
Link length supported for 50/125um fiber, units of 10m 17
1
Length(62.5um)
Link length supported for 62.5/125um fiber, units of 10m 18
1
Length(Copper)
Link length supported for copper, units of meters 19
1
Reserved
20-35
16
Vendor Name
SFP vendor name: JHA 36
1
Reserved
37-39
3
Vendor OUI
SFP transceiver vendor OUI ID 40-55
16
Vendor PN
Part Number: “JHA3202-85” (ASCII) 56-59
4
Vendor rev
Revision level for part number 60-62
3
Reserved
63
1
CCID
Least significant byte of sum of data in address 0-62 Extended ID Fields 64-65
2
Option
Indicates which optical SFP signals are implemented(001Ah = LOS, TX_FAULT, TX_DISABLE all supported) 66
1
BR, max
Upper bit rate margin, units of % 67
1
BR, min
Lower bit rate margin, units of % 68-83
16
Vendor SN
Serial number (ASCII) 84-91
8
Date code
JHA’s Manufacturing date code 92-94
3
Reserved
95
1
CCEX
Check code for the extended ID Fields (addresses 64 to 94) Vendor Specific ID Fields 96-127
32
Readable
JHA specific date, read only 128-255
128
Reserved
Reserved for SFF-8079 • Regulatory Compliance
The JHA3202-85 complies with international Electromagnetic Compatibility (EMC) and international safety requirements and standards (see details in Table following).
Electrostatic Discharge(ESD) to the Electrical Pins MIL-STD-883EMethod 3015.7 Class 1(>1000 V) Electrostatic Discharge (ESD)to the Duplex LC Receptacle IEC 61000-4-2GR-1089-CORE Compatible with standards ElectromagneticInterference (EMI) FCC Part 15 Class BEN55022 Class B (CISPR 22B)VCCI Class B Compatible with standards Laser Eye Safety FDA 21CFR 1040.10 and 1040.11EN60950, EN (IEC) 60825-1,2 Compatible with Class 1 laserproduct. • Recommended Circuit
SFP Host Recommended Circuit
• Mechanical Dimensions
Mechanical Drawing
-
♦ SONET OC-3/SDH STM-1
♦ Fast Ethernet
♦ Other Optical Links
*注：请准确填写信息，保持通讯畅通。我们将尽快与您联系
相关产品
如果您需要查询我们的产品或价目表，请留言
您给我们的电子邮件，我们将在24小时内与您联系。
