产品中心
深圳市锦昊安科技有限公司是一家专门为恶劣和苛刻环境设计的硬化以太网、PoE和光纤连接产品的制造商。
产品中心
- 产品描述
- 尺寸
- 订单信息
- 下载
- 应用
-
特征：
* 极低的 EMI 和出色的 ESD 保护
* 符合 RoHS 标准的零件
应用：
* 10GBASE-LR/LW 以太网
* SONET OC-192 / SDH
* 10G 光纤通道
描述：
JHA5960D-2733 和 JHA5960D-3327 双向 10Gb/s (SFP+) 收发器符合当前的 SFP+ 多源协议 (MSA) 规范。它们符合 10GBASE-LR/LW 以太网、SONET OC-192/SDH 和 10G 光纤通道 1200-SM-LL-L。按照 SFP+ MSA 的规定，可通过 2 线串行接口提供数字诊断功能。
l 绝对最大额定值
范围
象征
分钟
典型的
最大限度。
单元
储存温度 T S
-40
+85
摄氏度
电源电压 VCC T，R
-0.5
4
在
相对湿度 相对湿度
0
85
%
l 推荐 运行环境
范围
象征
分钟_
典型的
最大。
单元
外壳工作温度 热电偶_
-5
+70
摄氏度
电源电压 V CCT，右
+3.135
+3.465
在
电源电流 我抄送
450
嘛
功耗 PD _
1.5
在
l Electrical Characteristics (TOP = 0 to 70 °C, VCC = 3.135 to 3.465 Volts)
Parameter
Symbol
Min
Typ
Max
Unit
Note
Transmitter: Differential input voltage swing 180
700
mVpp
1
Transmit Disable Input H VIH
2.0
Vcc+0.3
V
L VIL
0
0.8
V
Transmit Enable Output H VOH
2.4
Vcc+0.3
V
L VOL
0
0.4
V
2
Input Differential Impedance Zin
80
100
120
Ω
Receiver Differential output voltage swing 300
850
mVpp
3
LOS Output H VOH
2.4
Vcc+0.3
V
2
L VOL
0
0.4
V
Output Differential Impedance Zon
80
100
120
Ω
Notes:
Note 1) TD+/- are internally AC coupled with 100Ω differential termination inside the module.
Note 2) Tx Fault and Rx LOS are open collector outputs, which should be pulled up with 4.7k to 10kΩ resistors on the host board. Pull up voltage between 2.0V and Vcc+0.3V.
Note 3) RD+/- outputs are internally AC coupled, and should be terminated with 100Ω (differential) at the user SERDES.
l Optical Parameters(TOP = 0 to 70°C, VCC = 3.135 to 3.465 Volts)
Parameter
Symbol
Min
Typ
Max
Unit
Ref.
Transmitter Bit Rate BR
9.9
11.3
Gb/s
Optical Wavelength JHA5960D-2733 λ
1260
1270
1280
nm
JHA5960D-3327 1320
1330
1340
Average output power Po
+1
+5
dBm
Optical Extinction Ratio ER
3.5
dB
Spectral width Δλ
1
nm
Side Mode Suppression Ratio SMSR
30
dB
Optical Eye Mask Compliant with IEEE802.3ae
Receiver Bit Rate BR
9.9
11.3
Gb/s
Optical Wavelength JHA5960D-2733 λ
1320
1330
1340
nm
JHA5960D-3327 1260
1270
1280
Receiver Sensitivity Sen
-22
dBm
1
Maximum Input Power PMAX
-7
dBm
LOS De-Assert LOSD
-23
dBm
LOS Assert LOSA
-33
dBm
LOS Hysteresis LOSH
0.5
4
dB
Notes:
Note 1) Measured with a PRBS of 231-1 at 1 x 10-12 BER and 3.5 dB extinction ratio.
l Pin Function Definitions
PIN #
Name
Function
Notes
1 VeeT Module transmitter ground 1
2 Tx Fault Module transmitter fault 2
3 Tx Disable Transmitter Disable; Turns off transmitter laser output 3
4 SDL 2 wire serial interface data input/output (SDA) 5 SCL 2 wire serial interface clock input (SCL) 6 MOD-ABS Module Absent, connect to VeeR or VeeT in the module 2
7 RS0 Rate select0, optionally control SFP+ receiver. When high, input data rate >4.5Gb/s; when low, input data rate <=4.5Gb/s 8 LOS Receiver Loss of Signal Indication 4
9 RS1 Rate select0, optionally control SFP+ transmitter. When high, input data rate >4.5Gb/s; when low, input data rate <=4.5Gb/s 10 VeeR Module receiver ground 1
11 VeeR Module receiver ground 1
12 RD- Receiver inverted data out put 13 RD+ Receiver non-inverted data out put 14 VeeR Module receiver ground 1
15 VccR Module receiver 3.3V supply 16 VccT Module transmitter 3.3V supply 17 VeeT Module transmitter ground 1
18 TD+ Transmitter inverted data out put 19 TD- Transmitter non-inverted data out put 20 VeeT Module transmitter ground 1
Note 1) The module ground pins shall be isolated from the module case.
Note 2) This pin is an open collector/drain output pin and shall be pulled up with 4.7K-10Kohms to Host_Vcc on the host board.
Note 3) This pin shall be pulled up with 4.7K-10Kohms to VccT in the module.
Note 4) This pin is an open collector/drain output pin and shall be pulled up with 4.7K-10Kohms to Host_Vcc on the host board.
l SFP Module EEPROM Information and Management
The SFP modules implement the 2-wire serial communication protocol as defined in the SFP -8472. The serial ID information of the SFP modules and Digital Diagnostic Monitor parameters can be accessed through the I2C interface at address A0h and A2h. The memory is mapped in Table 1. Detailed ID information (A0h) is listed in Table 2. And the DDM specification at address A2h. For more details of the memory map and byte definitions, please refer to the SFF-8472, “Digital Diagnostic Monitoring Interface for Optical Transceivers”. The DDM parameters have been internally calibrated.
Table 1. Digital Diagnostic Memory Map (Specific Data Field Descriptions)
Table 2 - EEPROM Serial ID Memory Contents (A0h)
Data Address
Length
(Byte)
Name of
Length
Description and Contents
Base ID Fields 0
1
Identifier
Type of Serial transceiver (03h=SFP) 1
1
Reserved
Extended identifier of type serial transceiver (04h) 2
1
Connector
Code of optical connector type (07=LC) 3-10
8
Transceiver
10G Base-LR 11
1
Encoding
64B/66B 12
1
BR, Nominal
Nominal baud rate, unit of 100Mbps 13-14
2
Reserved
(0000h) 15
1
Length(9um)
Link length supported for 9/125um fiber, units of 100m 16
1
Length(50um)
Link length supported for 50/125um fiber, units of 10m 17
1
Length(62.5um)
Link length supported for 62.5/125um fiber, units of 10m 18
1
Length(Copper)
Link length supported for copper, units of meters 19
1
Reserved
20-35
16
Vendor Name
SFP vendor name: JHA 36
1
Reserved
37-39
3
Vendor OUI
SFP transceiver vendor OUI ID 40-55
16
Vendor PN
Part Number: “JHA5960D-2733” or “JHA5960D-3327” (ASCII) 56-59
4
Vendor rev
Revision level for part number 60-62
3
Reserved
63
1
CCID
Least significant byte of sum of data in address 0-62 Extended ID Fields 64-65
2
Option
Indicates which optical SFP signals are implemented (001Ah = LOS, TX_FAULT, TX_DISABLE all supported)
66
1
BR, max
Upper bit rate margin, units of % 67
1
BR, min
Lower bit rate margin, units of % 68-83
16
Vendor SN
Serial number (ASCII) 84-91
8
Date code
JHA’s Manufacturing date code 92-94
3
Reserved
95
1
CCEX
Check code for the extended ID Fields (addresses 64 to 94) Vendor Specific ID Fields 96-127
32
Readable
JHA specific date, read only 128-255
128
Reserved
Reserved for SFF-8079 l Digital Diagnostic Monitor Characteristics
Data Address
Parameter
Accuracy
Unit
96-97 Transceiver Internal Temperature ±3.0 °C 98-99 VCC3 Internal Supply Voltage ±3.0 % 100-101 Laser Bias Current ±10 % 102-103 Tx Output Power ±3.0 dB 104-105 Rx Input Power ±3.0 dB l Regulatory Compliance
JHA5960D-2733 /3327 符合国际电磁兼容性 (EMC) 和国际安全要求和标准（详见下表）。
静电放电 （ ESD ）到电气引脚
MIL-STD-883E 方法 3015.7
1 级（>1000 伏） 静电放电 (ESD) 到单个 LC 插座
IEC 61000-4-2 GR-1089-核心
符合标准 电磁 干扰（电磁干扰）
FCC 第 15 部分 B 类 EN55022 B 类 (CISPR 22B)
VCCI B 类
符合标准 激光眼安全 FDA 21CFR 1040.10 和 1040.11 EN60950, EN (IEC) 60825-1,2
兼容 1 类激光 产品。
l 推荐电路
推荐主机板供电电路
推荐的高速接口电路
l 机械尺寸
*注：请准确填写信息，保持通讯畅通。我们将尽快与您联系
相关产品
如果您需要查询我们的产品或价目表，请留言
您给我们的电子邮件，我们将在24小时内与您联系。
