产品中心
深圳市锦昊安科技有限公司是一家专门为恶劣和苛刻环境设计的硬化以太网、PoE和光纤连接产品的制造商。
产品中心
Framed E1-FE+8RS232 interface Converter JHA-CE1F1R8
-
- Based on self -copyright IC
- Can realize monitor and control of remote equipment, OAM management data did not take up user’s timeslot and save E1 bandwidth
- E1 supports any timeslot set, the rate is 64K-2048K
- The local device can forced the remote device rate follow it
- Have indicator when the remote device is power-off or E1 line is broken or lose signal;
- Have the function of E1 interface loop back check, avoid the converter crashed because of interface loop return;
- The Ethernet interface supports jumbo frames (2036 Bytes);
- Inter-set dynamic Ethernet MAC address (4,096) with local data frame filtering function
- Ethernet interface supports 10M/100M, half/full duplex auto- Negotination, support VLAN
- Ethernet interface supports AUTO-MDIX (crossed line and straightly connected line self-adaptable );
-
产品分类：
PDH/语音多路复用器
接口转换器
以太网到E1转换器
- 产品描述
- 尺寸
- 订单信息
- 下载
- 应用
-
Framed E1-FE+8RS232 interface Converter JHA-CE1F1R8
Overview
This protocol converter (interface converter) using large scale FPGA design, providing a framing E1 interface and an Ethernet interface and 8channel RS232/422/485,it is possible to achieve 10 / 100Base-T Ethernet data over E1 channels transmission, is a high performance, self-learning Ethernet bridge. The device serves as an extension of Ethernet devices, use of existing networks (PDH / SDH / microwave, etc.) provided by the E1 channels to interconnect both ends of the lower cost Ethernet and serial interfaces. Built-loop test equipment capabilities to facilitate the opening and routine maintenance works.
Product Photo
19inch 1U Type
Features
- Have Ethernet monitor self-reset function, the equipment will not dead
- Provide 2 clock types: E1 master clock and E1 line clock;
- Provide 2 impedances: 75 Ohm unbalance and 120 Ohm balance;
- Support SNMP Network Management
- Serial Data Interface can be RS232/RS422/RS485/TTL optional
- Serial channel can transmit adaptable serial data asynchronously 300 Kbps-19200Kbps baud rate
- Serial data multiplexing in E1 support ITU-T R.111 jumping coding mode
- The local RS232 serial data can command the remote RS232 serial data loop-back to the local. This loop-back in the outer ring of RS232 data interface, you can test the RS232 interface chip without damage
- Serial port interface lightning-protection reached IEC61000-4-5 (8/20μS) DM(Differential Mode): 6KV, Impedance (2 Ohm), CM(Common Mode): 6KV, Impedance (2 Ohm)standard
Parameters
♦ E1 Interface
Interface Standard: comply with protocol G.703;
Interface Rate: n*64Kbps±50ppm;
Interface Code: HDB3;E1 Impedance: 75Ω (unbalance), 120Ω (balance);
Jitter tolerance: In accord with protocol G.742 and G.823
Allowed Attenuation: 0~6dBm
♦ Ethernet interface(10/100M)
Interface rate: 10/100 Mbps, half/full duplex auto-negotiation
Interface Standard: Compatible with IEEE 802.3, IEEE 802.1Q (VLAN)
MAC Address Capability: 4096
Connector: RJ45, support Auto-MDIX
♦ Serial Interface
Standard
EIA/TIA-232 RS-232 (ITU-T V.28)
EIA/TIA-422 RS-422 (ITU-T V.11)
EIA/TIA-485 RS-485 (ISO/IEC8284)
Serial Interface
RS-422:TXD+, TXD-, RXD+, RXD-, Signal Ground
RS-485 4 wires: TXD+, TXD-, RXD+, RXD-, Signal Ground
RS-485 2 wires: Data+(Correspond TX+), Data-（Correspond TX-）, Signal Ground
RS-232: RXD, TXD, Signal Ground
♦ Working environment
Working temperature: -10°C ~ 50°C
Working Humidity: 5%~95 % (no condensation)
Storage temperature: -40°C ~ 80°C
Storage Humidity: 5%~95 % (no condensation)
Specifications
Model Model Number:JHA-CE1F1R8 Functional Description 1channel framed E1 -FE +8RS232/422/485 converter，With E1 loopback detection function Port Description One E1 interfaces, Eight data interfaces (RS232) Power Power supply: AC180V ~ 260V；DC –48V；DC +24VPower consumption: ≤10W Dimension Product Size: 19inch 1U type 483X138X44mm (WXDXH) Weight 2.0KG/piece -
*注：请准确填写信息，保持通讯畅通。我们将尽快与您联系
相关产品
如果您需要查询我们的产品或价目表，请留言
您给我们的电子邮件，我们将在24小时内与您联系。
